|
|
Iscar Announces A New Family Of Slitting Cutters Utilizing Tang-Grip Technology And The Durability Of Sumo Tec Grades
Iscar right now offers a family of high-performance slitting tools that couple the convenience and security of Tang-Grip clamping with the increased sturdiness of the completely new Sumo Tec insert grades.
The conception, already confirmed successful in Tang-Grip parting tools, has now been extended to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanied by a specific hand tool, and are retained tightly in place without having the need without requiring clamps, upper jaws or set screws that can weaken the insert and hinder chip flow. The pocket design uses cutting forces to keep the insert seated firmly in position, removing any danger of insert pull-out. The Tang-Grip clamping system also fosters additional accurate slitting cuts plus increased pocket and insert lifespan.
Iscar's Sumo Tec insert grades feature a specialized post-coating treatment which substantially improves tool life and dependability.
Launched in late 2007, the revolutionary Sumo Tec treatment smooths the insert's coated surface to dispose of microscopic stress raisers, decrease heat and friction and improve chip flow. The result is improved toughness and resistance to chipping and built-up edge, all leading to greater tool lifespan. The golden-colored side on Sumo Tec inserts eases wear detection. Size for size, Tangslit cutters offer more teeth than Iscar's SGSF cutters, permitting higher feed rates.
Their improved rigidity leads to straighter, more accurate cuts and diminished vibration even in large-diameter cutters. The new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accommodate the exact same variety of inserts as Tang-Grip parting tools. Some other sizes will be added.
Obtainable Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate beneath a Sumo Tec TiAlN PVD coating, providing superior resistance to impact loads and built-up edge. This grade is recommended for slitting heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel.
IC830, offering additional toughness for heavier parting & grooving including interrupted cuts. It is suited for any stainless steel & high temperature alloys.
IC908, a hard, fine-grain substrate with exceptional chipping resistance, combined with a new Sumo Tec TiAlN PVD coating. It is ideal for nodular or gray cast iron.
IC928 and 928A, PVD TiAlN-coated tough grades fitting for stainless steel, high temperature alloys and other alloy steels. These grades are likewise favored for interrupted cuts and heavy operations.
Each Tangslit and Tang-Grip inserts are attainable in J- or C-type chipformer geometries from Iscar.
Iscar Recently Made Public Numerous Brand New Lines To Extend Their Family Of Milling Cutters
Iscar recently released a new family of High Speed Milling adjustable endmills and facemills that will improve milling of aluminum, non-metallics, cast iron and hardened steel. This should prove especially useful in the automotive and aerospace industries.
Iscar Adds Their Most Recent Creations To A Lengthy Line Of Prospering Hole Making Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.
A Few Of The Many Improvements In Carbide Inserts Coming From Iscar From Over The Years
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.
Completely New Cutters And Carbide Insert Shapes From Iscar To Better The Machining Procedure
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.
Push Pull Testing For Construction Industry With Calibrated Gauges. Stress Load Testing Methods For On Site Documentation To Testing Standards.
Push Pull Testing for the Railway industry for proof of reliable anchor fixings. Calibrated push pull force gauges are used for stress load testing along with tensile strength pull testing procedures. Proof of load testing undertaken, measured, recorded in a reliable and standard way to BS5080 Part 1 standards.
Various Developments Have Enlarged Iscar's Line Of Indexable Endmills For Elevated Productivity
Helido-Upfeed 04 Two years ago Iscar introduced the extremely efficient H600 indexable endmill line, based on conceptually new Helido-Upfeed double sided inserts with 6 cutting edges. The first insert launched was the H600 WXCU 0806..., which was designed for milling cutters in the diameter range of 50 to 125 mm.
Finding Out The Best Commercial Water Heater For You Needs
If you are in the market for a commercial water heater then consider what the needed application is and your overall cost to determine which is best for you. Since there are so many to choose from you may have to do some calculating in order to match the need.
The Simple Facts About The Graduate Jobs Obtainable In Europe.
Even if there is no formal education in medical school, new graduates planning to pursue such graduate careers can undergo training to cover the basics in health care to learn the non-specialized functions of the medical doctor.
|
More Articles
Blogroll
|
